The SDG800 series function/arbitrary waveform generator family outputs waveform functions up to up to 5 MHz (pulse), 10 MHz (square), 30 MHz (sine) and has a sampling rate of 125 MSa/s. They are powered with SIGLENT’s EasyPulse technology which produces low jitter, fast rising/falling edges without being affected by frequency, even at low duty cycle settings, allowing the user a wide range of pulse widths and transition times. This results in a much more versatile generator than other similar DDS designs.
- Innovative EasyPulse technology, can output pulses with low jitter and quick rising/falling edges
- Standard interfaces: USB Device, USB Host, supports U-Disk storage
- 10 nonvolatile storage spaces for user’s arbitrary waveforms
- Can be seamlessly connected to SIGLENT Digital Storage Oscilloscope
- Includes EasyWave, the powerful arbitrary waveform editing software
Comparison of edge under 1KHz pulse signal View more
Comparison of edge under 1KHz pulse signal
As shown in the figure, under 1KHz frequency, EasyPulse can keep quick rising/falling edge (20ns) while the edge of ordinary DDS is very slow.
Comparison of edge adjusting range under 1KHz pulse signal View more
Comparison of edge adjusting range under 1KHz pulse signal
EasyPulse edge adjustment has a wide range, while ordinary DDS pulse edge adjustment is limited.
Built-in 46 kinds of arbitrary waveforms (including DC) View more
Built-in 46 kinds of arbitrary waveforms (including DC)
SDG800 Series can output 5 kinds of standard waveforms and 46 kinds of commonly used waveforms, including common waveforms, mathematical functions, application functions, window functions and trigonometric functions.
Multiple modulation function View more
Multiple modulation function
SDG800 Series support multiple modulation function: AM, DSB – AM, FM, PM, FSK, ASK, PWM, linear/logarithmic sweep and burst.
Supports PC editing software EasyWave View more
Supports PC editing software EasyWave
Siglent’s SDG800 Series of generators support powerful PC editing software, EasyWave, which can output arbitrary waveforms with 14bit vertical resolution and 16 Kpts wave length. EasyWave provides 9 standard waveforms: Sine, Square, Ramp, Pulse, ExRise, ExpFall, Sinc, Noise and DC, which meet all engineers’ basic needs. In addition, it provides a variety of drawing modes including manual drawing, straightline drawing (including horizontal straightline, vertical straightline, point-to-point straightline), coordinate drawing and equation drawing, making it easy to generate complex waveforms. Multiple Document Interface management allows for simultaneous multiple-waveform editing. The SDG800 Series provides 10 nonvolatile storage spaces for arbitrary waveforms, and you can also edit and store more waveforms through the EasyWave software.
Printed Quick Start Guide (English)
Power cord designed for use with the instrument in the country of operation. Also available separately.
20 dB Attenuator
Power Amplifier to help boost signals from generators like the SIGLENT SDG family. Typical Input Impedance: 15kΩ Input: +/- 6.5V Vpp (Gain: X1) +/- 1.3 V (Gain: X10) Gain: Switched 10V/1V and 10V/10V Output Voltage: 25.4 Vpp Output Current: 1.12 A Slew Rate: ≥ 90 V/μs Overshoot: ≤ 4%. Compatible with all SIGLENT SDG series … Continued
Rackmount kit is designed for use with only one instrument. It is compatible with the SDG800, SDG1000, SDG1000X, SDG2000X, SDG6000X, and SDG5000 series function generators
BNC terminated coaxial cable (1 m length).
GPIB adapter converts GPIB signals to USB. For use with instruments that do not have a native GPIB bus Overview: USB-GPIB adapter is used to Siglent instrument， which has the USB Host interface but have no GPIB interface (eg SDS1000 series digital oscilloscope) . It can help this instrument connect to the device on the … Continued